Thermopanel Premium Waterproof Uncoupling/Decoupling Anti-Crack Membrane Matting - Prevent Cracks, Ensure Tile Durability - Available in 5m or 20m (5m x 1m)

Product Information

Butt joint the edges of the membrane. The overlapping blue mesh covers the joints between the roll lengths. BAL Flexbone 2Easy is to be laid with all necessary expansion joints in place. To ensure freedom of movement of the subsequent covering structure, tape all movement joints using a suitable proprietary self-adhesive tape to protect against the entry of the wet adhesive bedding material through the joints onto the existing floor during the installation. Although decoupling mats are waterproof on the surface, water can still get into the ground at the joints. Therefore, an appropriate sealing of the latter is necessary. Usually sealing tapes are used to prevent the penetration of moisture under the tiles. Step 5: Laying tiles

Mapei Mapeguard UM35 allows the distribution of stresses also on floorings subject to heavy loads; it is certified as EXTRA HEAVY COMMERCIAL RATING according to TCNA test reports complying with ASTM C 627 and is suitable for use in residential and commercial surroundings. Smooth it onto the surface of the mortar with a trowel, cutting the membrane at any seams to ensure a good fit if needed. Then, allow the adhesive to cure completely before moving on.Mapei Mapeguard UM35 Decoupling Membrane also guarantees that heat is distributed more evenly when applied on heated floors, including compact heated floors. ThermoSphere membrane is a patented polypropylene membrane complete with rounded square shaped dimples that form channels specifically designed to hold ThermoSphere heating cables in place. On the underside is an anchoring fleece to ensure the membrane bonds to the substrate. Simply press the heating cables into the membrane at variable spacing depending on your required output (w), and roll out over the space you wish to heat. Features & Benefits of the ThermoSphere Membrane Laying tiles over a concrete surface doesn't need to be daunting. Whether you use a decoupling membrane or a cement board, both methods offer a practical solution to enhance the longevity and aesthetics of your tiles. Once installed, the matting must be protected against heavy mechanical loads to avoid loosening it from the substrate or other damage. It is advisable to place running boards (especially in the centre of material transports) to protect it. Other protective measures, such as shielding of direct sunlight or protection from precipitation in exterior applications, may also be required. Carefully remove any moisture that may have gathered in the indentations of the studs before applying the thin-bed tile adhesive during tiling.

The distinguishing feature of DITRA is the existence of free space created by the configured channels on the underside of the matting. The free space provides a route for excess moisture and vapor to escape from the substrate that could otherwise cause damage to the tile layer above. Thus, DITRA effectively manages moisture beneath the tile covering. AddThis sets this geolocation cookie to help understand the location of users who share the information. Both types of decoupling membrane are available in a range of materials, including polyethylene, polypropylene, and rubber, each with its own unique properties and benefits. When choosing a decoupling membrane, it’s important to consider the type of flooring system you’re installing, as well as the specific requirements of your project, such as insulation, sound reduction, and load-bearing capacity.

Delivery times are Monday - Friday (excluding Bank Holidays) from 7:30am - 6:00pm. Most deliveries leave on Express Delivery for 1 - 3 working day delivery service. A 'working day' is Monday to Friday, excluding bank holidays. Weekends and bank holidays do not count as working days. Ditra matting should only ever go fleece side down. Apply the matting to the floor, fleece side down. Work the Ditra into the mortar, using a float or screed trowel in such a way that the fleece of the Ditra is solidly embedded in the bonding mortar throughout its entire surface (please observe the open time of the bonding mortar). The substrate must be even, load bearing and swept free from debris. Only if necessary, the floor can be levelled using a suitable BAL smoothing and levelling compound such as BAL Level Max. Schluter Ditra matting should be used primarily as a waterproofing layer when installing cover materials that are sensitive to moisture (e.g. natural stone or synthetic resin panels) or if moisture is expected to build up on the underside (e.g. in the case of green screed). When Ditra matting is installed in exterior applications, special protective measures may be required; e.g. shielding the installation from direct sunlight. The use of rapid setting thin-bed adhesives may be an advantage for certain projects. Make sure that the substrate you're fixing the matting to is clean. The substrate must be free of bond inhibiting components, be load bearing and be even. Any unevenness in the substrate must be levelled prior to the application of Ditra matting.

Basically, of course, the material requirement is decisive due to the number of square meters of the area to be decoupled. In the end, however, the materials used as well as the quality and functionality of the selected mat, but also the manufacturer, are decisive for the actual price. Standard mats are available for just a few euros per square metre, while particularly high-quality products are happy to make a multiple of that. On average, a realistic calculation can be made at around 10 euros per square metre, plus the cost of the flexible tile adhesive. All in all, decoupling mats are therefore not exactly cheap. With regard to a durable and above all damage-free tiled floor, the investment is definitely worthwhile. Apply the bonding adhesive to the substrate using a notched trowel. Ardex AF200 is the ideal bonding solution, although anydrate screeds may require additional preparation to ensure the substrate is dry and ready to recieve adhesive. We recommend the Ardex B1 2mm notched trowel for use with decoupling membranes. The adhesive must bond to the substrate and mechanically anchor the fleece on the underside of the Ditra Matting. You can verify the compatibility of all materials prior to installation either with our friendly Tile Fix Direct customer service team, or with Schluter. In principle, modern decoupling systems are therefore suitable for almost any difficult substrate, such as concrete, mixed subfloors, wooden floorboards, chipboard, cement or dry screed, old tiles and many more. Which decoupling mat is best in a specific case, however, depends on the respective area of application and the associated requirements. This is because in addition to the actual function of decoupling, most mats also have other advantages.

Tile Giant is your premier source for professional-grade tile decoupling membranes, featuring trusted brands like Durabase and Schluter. Our range is meticulously designed to meet the exacting standards of professional fitters. We understand that the foundation of every successful tile project lies in meticulous attention to detail. Schluter Ditra matting should be covered with protective running boards if the transport of material makes it necessary to walk over the matting. Textile mats in particular, such as a PCI decoupling mat, are characterised by improved footfall sound insulation. While other systems, such as Schlüter Ditra decoupling mats, are universally applicable at all, as they combine multifunctional properties in one product with decoupling, sealing, vapour pressure compensation and drainage. How are decoupling mats installed? Apply a layer bonding adhesive like Ardex AF200 to the level substrate using a 3x3mm or 4x4mm notched trowel. Cut DITRA matting to size if required, then embed the anchoring fleece on the underside of the matting into the adhesive so that its entire surface is strongly bonded.