Joined in 2023 
82 
63 About this deal
ZERO side play, low-friction travel on table saws with square-sided miter slots measuring 3/4 inch (19 mm) wide, 3/8 inch (9.5 mm) deep, and with or without a 15/16 inch (23.7 mm) T-slot at the bottom. The miter bar's adjustment range accommodates actual slot widths between 0.740 and 0.765 inch (18.8 - 19.4 mm) The sled can be set up on either the left side or right side of the blade, and a renewable Drop Panel provides zero clearance tearout control on both sides of the blade.
INCRA Miter Gauge V27 is engineered to provide a high performance, yet low cost upgrade for any tool in need of a better miter gauge such as a Table Saw, Band Saw, Router Table, Disk Sander or Belt Sander. Six expansion disks adjust both sides of the bar for ZERO side play, low-friction travel on all table saws with standard miter gauge channels, including Delta,
INCRA Miter 5000
The tape on the fence is movable, so it can be calibrated on the fly with fence moves and you’ll notice they thought ahead about that whole fence not touching the blade thing as they even give you some numbers on the other side of zero. The gauge can rotate 90 degrees in both directions and the positive stops are achieved via a saw-tooth design that’s incredibly effective. When the teeth are engaged, there’s zero play and you have nothing but confidence in your setting.
The expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard 3/4" x 3/8" or near-standard miter gauge channels, including Delta, Craftsman, imports, etc. This means that all of INCRA's incredible precision will actually show up in your work because the bar CAN'T wiggle around in the miter slot. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.765". Assembly took about 15 minutes but most of that time was spent fiddling with the darn stop. This is one of those parts you wish they included pre-assembled. The Kreg Precision Miter Gauge features an aluminum protractor head, aluminum fence, and an aluminum miter bar. That’s a bold choice for a miter bar as I can see it being a potential weak point in the design, especially at a length of 24” (the longest you’ll find on the market). The gauge can rotate 50 degrees in both directions and has a resolution of 1/10 of a degree thanks to a high visibility vernier scale. It has 9 positive stops that are engaged with a brass pin, though this is an unfortunate design choice as the pin is not fixed to the gauge and if you should happen to turn the gauge upside down, the pin falls out. I also noticed a little play at each detent, but you can overcome it by putting a good amount of pressure down on the pin and then tightening the protractor head.The 3/4" x 3/8" steel miter bar features up to six independent nylon expansion rings to ensure a perfect fit with the slot in your saw. A removable steel T-Clip helps to keep the miter gauge on your saw when fully retracted for wide crosscuts. As shown, the same INCRA HoldDown Clamp also keeps your fingers comfortably away from the blade when cutting workpieces that are too small to safely hold by hand. Shown here with optional INCRA Miter Gauge. Miter Gauge not included! Blade cover removed for demonstration purposes. Do not work without blade cover! Flip Fences can be used with any INCRA Miter Gauge and the Flip Shop Stop. Flip Fences are NOT compatible with the standard Shop Stop.
The Miter 1000's adjustable miter bar will fit square-sided miter slots measuring 3/4" wide, 3/8" deep, and with or without a 15/16" T-slot at the bottom. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.765". What makes the Incra 1000HD different is that it’s HIGH DEFINITION! If you look at the protractor head you’ll see more teeth than my new puppy Abby. That’s 180 positive stops. Yeah that’s right. A stop for every degree including 90 in both directions. And it has 1/10 of a degree resolution thanks to the vernier cursor. The V120's adjustable miter bar will fit square-sided miter slots 3/4" wide, 3/8" deep, and either with or without a 15/16" wide T-slot at the bottom. The miter bar's adjustment range accommodates slot widths between 0.740" to 0.760".Doubles Any Miter Gauge's Crosscut Capacity to 24" and Securely Holds Even the Smallest Workpieces for Safe Accurate Cuts Miter gauges don’t offer control or accuracy when pulled beyond the front of the saw, while the 5000 can crosscut 23" x 34" plywood cabinet sides with ease on most full size 10" table saws. INCRA's Miter Express offers any miter gauge owner a safe and accurate cross-cutting and mitering platform. Shown above with an optional INCRA Miter 1000SE mounted and ready, the Express features 2 embedded T-Slot channels to secure the included Hold Down Clamp and Outboard Fence Support. These slots are also invaluable for mounting your own custom Jigs and Fixtures. Summary: This gauge is an absolute beauty and the materials seem to be of a higher than typical quality. There are seeds of greatness here but there’s a major failure in execution, several missed opportunities, and a couple of regrettable choices. There’s always a chance that I received a bad unit, but I’ve heard from others who have the same issues and many of the problems with this thing are just the way it was designed. Furthermore, my personal experience with their technical service left a lot to be desired. Am I being a little hard on Harvey here? You bet I am. When a company charges 30% more than the nearest competitor, they’ve got something to prove. And judging from the unit I received (and the customer service), Harvey came up short. Final Thoughts Eliminates All Drag Between Workpiece and Table Saw, ESPECIALLY for Extra Large Workpieces Superb Crosscut &Mitering Control
INCRA's Miter Express offers any miter gauge owner the safest and most accurate cross-cutting platform available. Miter gauge & fence sold separately; use the Miter Express with ANY standard miter gauge! Available for traditional 3/4” x 3/8” miter slots and Shopsmith machines. Shown above with an optional INCRA Miter 1000SE mounted and ready, the Express features 2 embedded T-Slot channels to secure the included Hold Down Clamp and Outboard Fence Support. These slots are also invaluable for mounting your own custom Jigs and Fixtures. This Special Edition Miter Fence telescopes from 36" to a full 64" length. Includes the Dual Flip Shop Stop and INCRA's patented Automatic Positioning Control.Criteria: I included every manufacturer I could find that makes a miter gauge with a fence. There are several other miter gauges on the market that do not come with a fence, but to keep the playing field even I did not include those in this review. Six expansion disks adjust both sides of the bar for ZERO side play, low-friction travel on all table saws with standard miter gauge channels, including Delta, Craftsman, imports, etc. An excellent fit in the channel directly transfers the Miter 1000HD's incredible accuracy to your project. The Miter 1000's adjustable miter bar will fit square-sided miter slots measuring 3/4" wide, 3/8" deep, and with or without a 15/16" T-slot at the bottom. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.765". The Miter V27's compact protractor design works on applications typically not candidates for aftermarket gauges because of the narrow distance between the cutter and miter slot. For adequate support laterally, the Miter 5000 requires a minimum of 254mm (10") from the side of the outer edge of the miter slot to either the left or right edges of the saw (sled can be installed on either side of the blade). The expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard 3/4" x 3/8" or near-standard miter gauge channels, including Delta, Craftsman, imports, etc. The miter bar's adjustment range accommodates actual slot widths between 0.740" and 0.760".
Great Deal 
New Comment