Manns Premier UV Decking Oil 5L - Natural Oak - A Multi-Purpose Decking Oil, That Protects Against Weathering & UV Damage

Product Information

What amazed me the most was the oil’s protective qualities. After treating the table, I noticed that water beaded up on the surface instead of soaking in, making it easy to clean and maintain. Plus, it worked wonderfully on both interior and exterior wood surfaces, giving it versatility and broad applicability. Offers moderate shine and enhances the wood’s natural colour, making it more vibrant and attractive

If the finish is an oil it should have soaked into the surface of the wood and will naturally wear away over time, it will not peel and flake unless it has been over applied.Oils can not be removed with a stripper, some lift will come from using a pressure washer, but take care not to hold the nozzle too close to the woods surface as this will damage and splinter the wood.Barretine - another solvent based oil. Also offers UV protection in a clear varnish and has marginally less performance than the Manns whilst still being a high performer Its a bit of a battle to maintain the natural colour of these types of woods I am afraid, they will just naturally silver and for many people this is the desired result. It is a balancing act to get the best for the wood, protection or colour. As you have a dog I would recommend considering an oiled finish, this will be far easier to maintain over time, oils soak into the wood surface and so is less likely to be effected by claw marks, and even if it is, you can simply patch repair and the oil will blend well. Oils are also easy to maintain as they wear, simply ensure the surface is clean and dry and then you are able to apply a top up coat when needed, usually around 1 or 2 years down the line, depending on use. Only apply in double figure temperatures and when the weather is set to be dry for at least the minimum drying time displayed on the tin. Single figure temperatures, damp or wet conditions could adversely affect the application and final finish of the product

Can reduce the visibility of the wood grain due to the pigmented film between the timber and the surfaceResistant to changeable weather conditions, general wear and tear, prevents wood from greying and splitting. Always, stir the contents of the tin thoroughly, at least for a couple of minutes before applying. This ensures that colour pigments and other important ingredients of the product are well distributed and not concentrated at the bottom of the tin. For the best protection, apply an exterior wood preservative to protect against mould, algae, dry rot, woodworm and wood related diseases I recently used this Furniture Clinic Danish Oil on a vintage table I got from a charity shop, and I was thoroughly impressed with the results. The table had some wear and tear, but after applying the Danish Oil, its natural beauty shone through. The oil’s natural blend of oils and resins penetrated deep into the wood, creating a hard and durable satin finish.

An oil soaks into the surface of the wood and will wear away over time. A stain, paint or varnish is a surface sealer and over time could peel and flake, exposing bare wood underneath. Paint, stains or varnishes can be removed with a stripper such as Paint Panther Paint and Varnish Remover. Oils unfortunately can not and if you can’t wait for them to wear away naturally the you can use a pressure washer to remove much of it, care must be taken not to damage the wood however. This period is often around 10 – 12 weeks and can allow the wood to start to silver some, it depends very much on the time of year and level of exposure to the wood. You may find that it this time of year you may get away with minimal fading as we go through the winter. And the wood may then be ready for application come the Spring. I am sorry for the delay in response, it is a super busy time here at Wood Finishes Direct. A stain or paint is a surface sealer and is likely to, over time, peel and flake, if the treatment appears to be lifting it is likely that this is the finish you have and this can be removed with a pressure washer or stripper product such as the Paint Panther Paint and Varnish Remover You’ve got to factor in the increase in performance of some water based and the decline in performance of some solvent based. So a sneak peak of what Wood Finishes Direct found out in their trials - and I stress they haven’t published the results yet so this may change: When you start adding a little colour, the factor increases, so a light or natural oak for example will bring you up to a 20 – 30 factor and then a dark oak, rosewood, or dark brown will bring you up to a factor 50. This is the best way to maintain the natural colour of the wood over time, but of course if you don’t want to add colour then a clear oil with UV stabalisers will require annual top up.However, specific information about the ease of application and enhanced appearance is not provided for the Manns Premier UV in the given details. Depending on individual needs and preferences, customers may prioritize the UV protection and weather resistance provided by the Manns Premier UV 5L Clear or the comprehensive features of the RONSEAL Ultimate Natural 5L, including its natural look and unique penetrating formula. Customer review:"Last used 2 years ago and finish lasted well. Very good product and so simple to apply by brush. Slightly more expensive but would recommend for quality."

A slight concern I had was the tendency of the product to clog when left in a spray applicator. However, with a bit of cleaning and attention, it can still be used effectively in this manner. Thank you for getting in touch with your question. It is a common question asked for beautiful tropical hard woods such as Ipe, Balua and Iroko. Jatoba is a less common one, however if it is anything like the others it will require a period of weathering. Tropical hardwoods tend to have a naturally high oil content when they are relatively new, these oils will prevent the uptake or adhesion of any product that you try to apply. So a weathering period to allow these oils to naturally disperse is the recommendation. Whether you want an easy to complete maintenance that needs regularly redoing or a more comprehensive one that you can apply and forget for a few years If you do find there is any fading of the wood, then you could look at using a reviver product such as the Osmo Wood Reviver Gel this can restore the natural tones of the wood. It also brings out the natural shade of wood on various surfaces like fences, sheds, and hot tubs. While the RONSEAL Ultimate Natural 5L offers a “natural look,” the Liberon Clear Protection is specified as providing a “clear finish.” The choice between the two would depend on personal preferences regarding the desired appearance and the additional feature of UV protection provided by the Liberon oil.Ahandytip before we get started is to keep an eye on the weather forecast as we are going to need a couple of clear days to get the project done properly trust me it’ll be worth it in the end.