MYSON Radiator Bleed Valve/Screw/Vent/Nipple Replacement

Product Information

Make sure that you turn the heating off – the last thing you want is a trip to the hospital for scalding yourself!” Frequently Asked Questions They’re typically placed at the top of the radiator because any air that will be trapped inside will be forced upwards by the pressurised water below. Personally, I know I need to drain, flush, descale, and refill, including inhibitor every couple of years anyway, because of a combination of hard water and the lowest point being a blower unit that easily clogs, in a room that needs the heat. Getting the sludge out of that is a good few hours' work; fixing this valve would be a minor addition to the effort. I'd one of each main type to have on hand, but consider it not guaranteed to fit so wouldn't remove the old one when the shops are shut. Products Keep the valve open until the water stops flowing out although if you are unable to open the bleed valve, move on to step 4. Step 4 – Remove the Bleed Plug We can provide dedicated support for the commercial and specification market in areas such as hotels, schools, hospitals and a variety of other commercial installations

Now you will need to clean around openings, insert the plugs and do them up nice and tight letting the PTFE tape create the seal. Step 6 – Turn on the System After removing the plugs there will be a bit of air in the system that should make it to the AAV although now would be a good time to make sure all of the radiators are bled. ConclusionI'd be a little wary of relying on the outside nut long term in case of leaks developing. Most of my radiators need bleeding at this time of year, a couple of them more than once, so that might mean a few openings. New ones often have an o-ring seal which can tolerate opening, but older ones didn't. The MYSON TRV2 range includes over 20 different products with compression or push fit connections in 10mm, 15mm and ½” sizes

MYSON Controls produce a wide range of thermostatic radiator valves (TRVs) to suit any application, from standard domestic requirements to polished decorative products.Our TRV valves are perfect for any project, whether it’s new-build, self-build, social housing or large commercial projects, MYSON have the optimum productto complement our heat emitter range This step is important to prevent leakage as new plugs alone will not be enough to prevent leakage so the threads will need to be wrapped with PTFE Tape. This is especially true when using new plugs on older radiators. Our unique range of TRVs includes TRV2, including a Petite version, remote sensor heads, TRV bodies, an attractive decorative model, as well a specially designed TRV kits to complement our LST radiator range. Bleed plugs can often be removed when a system needs draining or the radiator needs flushing and may be due to age, wear and tear or poor technique, you may end up struggling. How to Replace Radiator Bleed Valves

You should be able to isolate an individual radiator with its own valves, with the caveat that some thermostatic valves leak a little when turned off especially if the room gets cold (mainly old ones but not necessarily). The balancing valve on the other end, which is almost always present, can be reset by counting turns as you close it then opening it the same amount. You'll get some water out, and it will be dirty, so protect the floor, walls etc. There are a number of reasons why you need or want to replace your bleed valve but don’t worry, it is not a difficult task so keep reading and we will cover that shortly. Leaks Another reason could be because the bleed valve has been painted over and doesn’t look very good and you want to have nice shiny fittings on your radiators.

🍪 Privacy & Transparency

You will want to take your new plugs and wrap the PTFE tape around the threads, pressing the tape into the grooves as you go. How many times you wrap the thread will depend on the valve, but 3 times around is a good benchmark. Our PETITE range has over 10 different products with compression or push fit connections in 10mm, 15mm and ½” sizes

Note: If you were unable to open the bleed valve in step 3 – undo the plug slowly and be prepared for some water to escape. Step 5 – Wrap Your New Plugs with PTFE Tape

Registration for our free email newsletter.

Now you will need your adjustable spanner to remove the bleed plug (and the blank on the other end). The time to fix is either now or after this winter but before next winter. I'd go for the latter because I'd fit it in with work that's likely anyway then. The Unisenza Plus Receiver RF can be used for the wireless control of a boiler, pump, or zone valves in a central heating system.